Einzelnen Beitrag anzeigen
Alt 17.06.2004, 12:46   #44 (permalink)
GrandMasterSeksay
Overclocker
 
Benutzerbild von GrandMasterSeksay
 

Registriert seit: 17.06.2004
Beiträge: 376

GrandMasterSeksay kann nur auf Besserung hoffen

Standard

So, bin zwar erst ein paar Minuten hier,
aber diese Streiterei bringt mich zur Weißglut.
Für alle die es 'net kapieren (wollen), die X800Pro ist schon ein ganzen Stücke schneller als die 9800XT. Und nur die X800 XT ist doppelt so schnell, wie die 9800XT.
Bin zwar ein bisschen schreibfaul geworden, aber verlinken klappt alle mal:
Testbericht - Tom's Hardware - Testbericht, für alle, die nicht glauben wollen, dass ATi Unmögliches möglich macht
CPU-Auslastung bei High-End-Grafikkarten <= zeigt m.M.n. den Grund, warum die 6800 Ultra so schnell ist
Kaufempfehlungen:
256MB Sapphire Radeon X800 Pro Lite-RTL - € 389.99
256MB Sapphire Radeon X800 Pro Full-RTL - € 419.99
256MB HIS Excalibur X800 Pro IceQ II RTL - € 435.99
Dann kann man die X800 Pro noch per Hardware-Mod zur X800 XT modifizieren, und man hat eine Radeon, doppelt so schnell wie die bisherige Top-Karte (9800XT) zu etwa dem gleichen Preis.
Zitat:
You need:
1. An X800pro. (This has so far only been tested on Sapphire cards)
2. Arctic silver or replacement thermal paste
3. Small philips (+) Screwdriver
4. Conductive paint or soldering kit
5. Small, sharp knife
6. MSDOS bootdisk
7. Flashrom 2.37 ( http://www.overclockers.ru/cgi-ATI_flashrom_2.37.rar )
8. ATi Radeon X800XT Bios ( http://softmod.ocfaq.com/bios/ATI.X8....Samsung16.bin )
9. ATiTool ver 0.0.20 ( http://atitool.ocfaq.com/ATITool_0.0.20.exe )
10. ATi Catalyst 4.5 Beta ( http://files2.guru3d.com/ati/RX800614106444.exe )
11.(Optional) A PCI graphics card incase the bios flash goes wrong
12. Driver Cleaner 3 ( http://www.driverheaven.net/cleaner/ )

Steps to take.

1. Use drivercleaner to remove any previous drivers, then prepare your MSDOS boot disk, and put ATIflash and the X800XT BIOS on a seperate floppy. Might be worth renaming the XT bios to 'XT.bin' or something simple.
2. Boot the PC via the DOS disk
3. At the command prompt type 'FLASHROM.EXE -s 0 original.bin' (without quotes - This will backup your original bios to 'original.bin'
4. Flash the XT BIOS to your card by typing 'FLASHROM.EXE -p 0 XT.bin -f' where XT.bin is the name of your XT BIOS.
5. Confirm that the flash procedure completed and power off your PC.
6. Remove the card from your PC
7. Lay the card down on the heatsink side and undo the 3 screws holding the heatsink/fan on.
8. Carefully remove the heatsink and put it somewhere safe.
9. Clean off any excess thermal paste with a soft, dry cloth. Be gentle with it!
10. Find the outlined in red points shown here ( http://www.andovernaturalproducts.co.uk/x800Pro1.jpg)
11. You want to join the leftmost two, but first you need to scrape the tops of the 2 points with your sharp knife. Scrape away very carefully until you see lightly coloured copper. These are your contact points!
12. Join the 2 points up with conductive paint or solder
13. Re-apply some thermal paste, refit heatsink and refit card to PC
14. Power on and boot into windows
15. Install Catalyst 4.5 Beta's
16. Check with ATiTool that you have 16 pipes enabled by clicking 'Settings'
17. Run a 3D-intensive application or game such as 3DMark and see if all is ok
Quelle - Hardware MOD
Und für alle, die nebenbei meinten, man merke den Unterschied zw. 256 und 128 MB-GraKa-RAM nicht, denkt mal zurück an die Zeit, als man mit 133 Mhz CPU's gesagt hat, das Non-Plus-Ultra wäre erreicht . Die passende Software kommt noch. Und dann wird gezokkt und in Games die Gegner niedergerockt!

Für die, die meinen, ATi cheate, sollten sich mal einen richten Beitrag alla Tom's Hardware
Zitat:
durchlesen
und sich danach nochmal äußern, bzw. sich korrigieren.
GrandMasterSeksay ist offline   Mit Zitat antworten