Du kanst dir einen RGB-Signal - Adapter aus einem Scartkabel bastel, ich hab es selbst probiert. Ich habe eins von Scart auf VGA adaptiert und es dann von VGA auf D_Sub (analoger Grafikkartenstecker). Die Pinbelegungen sind so:
[font=Times New Roman]
Scart-Stecker Pinbelegung [/font]
[font=Times New Roman]Pin [/font]
[font=Times New Roman]Signal[/font]
[font=Times New Roman]Pin [/font]
[font=Times New Roman]Signal[/font]
[font=Times New Roman]1 [/font]
[font=Times New Roman]Audio-R Ausgang[/font]
[font=Times New Roman]12 [/font]
[font=Times New Roman]Datenleitung 2[/font]
[font=Times New Roman]2 [/font]
[font=Times New Roman]Audio-R Eingang[/font]
[font=Times New Roman]13 [/font]
[font=Times New Roman]Rot Masse[/font]
[font=Times New Roman]3 [/font]
[font=Times New Roman]Audio-L Ausgang[/font]
[font=Times New Roman]14 [/font]
[font=Times New Roman]AV Schaltsp. Dat. Masse [/font]
[font=Times New Roman]4 [/font]
[font=Times New Roman]Audio Masse[/font]
[font=Times New Roman]15 [/font]
[font=Times New Roman]Rot Signal[/font]
[font=Times New Roman]5 [/font]
[font=Times New Roman]
Blau Masse[/font]
[font=Times New Roman]16 [/font]
[font=Times New Roman]Austastsignal[/font]
[font=Times New Roman]6 [/font]
[font=Times New Roman]Audio-L Eingang[/font]
[font=Times New Roman]17 [/font]
[font=Times New Roman]F-BAS Masse[/font]
[font=Times New Roman]7 [/font]
[font=Times New Roman]
Blau Signal[/font]
[font=Times New Roman]18 [/font]
[font=Times New Roman]Austastsignal Masse[/font]
[font=Times New Roman]8 [/font]
[font=Times New Roman]AV Schaltspannung[/font]
[font=Times New Roman]19 [/font]
[font=Times New Roman]F-BAS Ausgang Signal[/font]
[font=Times New Roman]9 [/font]
[font=Times New Roman]Grün Masse[/font]
[font=Times New Roman]20 [/font]
[font=Times New Roman]F-BAS Eingang Signal[/font]
[font=Times New Roman]10 [/font]
[font=Times New Roman]Datenleitung 1[/font]
[font=Times New Roman]21 [/font]
[font=Times New Roman]Abschirmung[/font]
[font=Times New Roman]11 [/font]
[font=Times New Roman]Grün Signal[/font]
[font=Times New Roman] [/font]
[font=Times New Roman] [/font]
[font=Times New Roman][/font]
[font=Times New Roman]
VGA-Stecker Pinbelegung [/font]
[font=Times New Roman]Pin [/font]
[font=Times New Roman]Signal[/font]
[font=Times New Roman]Pin [/font]
[font=Times New Roman]Signal[/font]
[font=Times New Roman]1 [/font]
[font=Times New Roman]Rot Signal[/font]
[font=Times New Roman]12 [/font]
[font=Times New Roman]SDA-12 C Daten[/font]
[font=Times New Roman]2 [/font]
[font=Times New Roman]Grün Signal[/font]
[font=Times New Roman]13 [/font]
[font=Times New Roman]H-SYNC/C-SYNC Signal[/font]
[font=Times New Roman]3 [/font]
[font=Times New Roman]Blau Signal[/font]
[font=Times New Roman]14 [/font]
[font=Times New Roman]V-SYNC Signal[/font]
[font=Times New Roman]4 [/font]
[font=Times New Roman]-[/font]
[font=Times New Roman]15 [/font]
[font=Times New Roman]SCL-12C Datentakt[/font]
[font=Times New Roman]5 [/font]
[font=Times New Roman]Masse[/font]
[font=Times New Roman] [/font]
[font=Times New Roman] [/font]
[font=Times New Roman]6 [/font]
[font=Times New Roman]Rot Masse[/font]
[font=Times New Roman] [/font]
[font=Times New Roman] [/font]
[font=Times New Roman]7 [/font]
[font=Times New Roman]Grün Masse[/font]
[font=Times New Roman] [/font]
[font=Times New Roman] [/font]
[font=Times New Roman]8 [/font]
[font=Times New Roman]Blau Masse[/font]
[font=Times New Roman] [/font]
[font=Times New Roman] [/font]
[font=Times New Roman]9 [/font]
[font=Times New Roman]+5V vom PC[/font]
[font=Times New Roman] [/font]
[font=Times New Roman] [/font]
[font=Times New Roman]10 [/font]
[font=Times New Roman]SYNC Masse[/font]
[font=Times New Roman] [/font]
[font=Times New Roman] [/font]
[font=Times New Roman]11 [/font]
[font=Times New Roman]Monitor ID 0[/font]
[font=Times New Roman] [/font]
[font=Times New Roman] [/font]
[font='Times New Roman'][/font]
- das einzige, was am Scart fehlt ist das SYNC - Signal, deshalb kann man diesen Adapter nicht an einen Röhrenmonitor anschließen. mit Flachbildschirmen müsste es gehen.