[DerKleineFreak]

Almost every EIDE or SATA hard disk includes S.M.A.R.T. data. That information is collected by the drive itself and contains data that the manufacturer considered relevant to check reliability. The data is made up of several attributes that have a current value, a worst one, a threshold, some raw data, and some flags. Basically, when any attribute's current value is below its threshold, the hard disk is considered unreliable and likely to fail. By using several techniques, this report tries to give a wider range of info, basing its analysis on advanced comparisons with normal values based on real hard disks and on expert-like checks. The final results are not to be taken as an absolute truth, but they are a very good approach to what a professional would say about your hard disk status.
Your hard disk is a ST3200822A with firmware 3.01.
The average temperature for this hard disk is 36C (MIN=25C MAX=49C) and yours is 39C.
Your hard disk's S.M.A.R.T. attributes are now being analyzed and a full report about the reliability, health and status of your hard disk is generated:
Your hard disk is not below any attribute threshold. This is good.
Your hard disk was never below any attribute threshold. This is good.
Your hard disk is now being compared to real data used to define normal values for your specific hard disk model. This way, the analysis can automatically use proper operating ranges. The images give you an idea of how each attribute is within such range. Current and raw values are shown for easier reference for experienced users. There are 959 hard disk models in the current archive.

Attribute Current Raw Overall
8 Raw Read Error Rate 60 27298152 Very good
6 Spin Up Time 97 0 Good
10 Start/Stop Count 100 525 Very good
10 Reallocated Sector Count 100 0 Very good
6 Seek Error Rate 77 54506033 Good
10 Power On Hours Count 99 1484 Very good
10 Spin Retry Count 100 0 Very good
1 Power Cycle Count 99 1393 Normal
8 Hardware ECC Recovered 60 27298152 Very good
10 Current Pending Sector 100 0 Very good
10 Offline Uncorrectable Sector Count 100 0 Very good
10 Ultra DMA CRC Error Rate 200 0 Very good
10 Write Error Rate 100 0 Very good
10 TA Increase Count 100 0 Very good

All of the attributes of your hard disk have normal values. This is good.

The overall fitness for this drive is 95%.
The overall performance for this drive is 95%.

Almost every EIDE or SATA hard disk includes S.M.A.R.T. data. That information is collected by the drive itself and contains data that the manufacturer considered relevant to check reliability. The data is made up of several attributes that have a current value, a worst one, a threshold, some raw data, and some flags. Basically, when any attribute's current value is below its threshold, the hard disk is considered unreliable and likely to fail. By using several techniques, this report tries to give a wider range of info, basing its analysis on advanced comparisons with normal values based on real hard disks and on expert-like checks. The final results are not to be taken as an absolute truth, but they are a very good approach to what a professional would say about your hard disk status.
Your hard disk is a SAMSUNG SP2504C with firmware VT100-41.
The average temperature for this hard disk is 32C (MIN=23C MAX=44C) and yours is 36C.
Your hard disk's S.M.A.R.T. attributes are now being analyzed and a full report about the reliability, health and status of your hard disk is generated:
Your hard disk is not below any attribute threshold. This is good.
Your hard disk was never below any attribute threshold. This is good.
Your hard disk is now being compared to real data used to define normal values for your specific hard disk model. This way, the analysis can automatically use proper operating ranges. The images give you an idea of how each attribute is within such range. Current and raw values are shown for easier reference for experienced users. There are 959 hard disk models in the current archive.

Attribute Current Raw Overall
1 Raw Read Error Rate 100 0 Normal
10 Spin Up Time 100 5952 Very good
10 Start/Stop Count 100 132 Very good
10 Reallocated Sector Count 253 0 Very good
10 Seek Error Rate 253 0 Very good
10 Seek Time Performance 253 0 Very good
10 Power On Hours Count 253 244 Very good
10 Spin Retry Count 253 0 Very good
10 Calibration Retry Count 253 0 Very good
10 Power Cycle Count 100 121 Very good
10 Unknown attribute 187 253 0 Very good
5 Unknown attribute 190 130 36 Good
10 Hardware ECC Recovered 100 984735 Very good
10 Reallocated Event Count 253 0 Very good
10 Current Pending Sector 253 0 Very good
10 Offline Uncorrectable Sector Count 253 0 Very good
10 Ultra DMA CRC Error Rate 200 0 Very good
1 Write Error Rate 100 0 Normal
10 Soft Read Error Rate 253 0 Very good
10 TA Increase Count 253 0 Very good

All of the attributes of your hard disk have normal values. This is good.

The overall fitness for this drive is 90%.
The overall performance for this drive is 90%.

Almost every EIDE or SATA hard disk includes S.M.A.R.T. data. That information is collected by the drive itself and contains data that the manufacturer considered relevant to check reliability. The data is made up of several attributes that have a current value, a worst one, a threshold, some raw data, and some flags. Basically, when any attribute's current value is below its threshold, the hard disk is considered unreliable and likely to fail. By using several techniques, this report tries to give a wider range of info, basing its analysis on advanced comparisons with normal values based on real hard disks and on expert-like checks. The final results are not to be taken as an absolute truth, but they are a very good approach to what a professional would say about your hard disk status.
Your hard disk is a ST314220A with firmware 3.07.
Your hard disk is not in the current database.
An hard disk with the same model, but with a different firmware was found:
Your hard disk is not reporting its temperature. This is normal for this hard disk model.
New hard disks are added as soon as valid statistics can be computed.
Come back soon to check your hard disk against a new database.
Your hard disk's S.M.A.R.T. attributes are now being analyzed and a full report about the reliability, health and status of your hard disk is generated:
Your hard disk is not below any attribute threshold. This is good.
Your hard disk was never below any attribute threshold. This is good.
Since your hard disk is not in the current database, overall ratings and pictures will be based upon realistic values, but you should carefully check the results.

Attribute Current Raw Overall
9 Raw Read Error Rate 86 28475721 Very good
7 Spin Up Time 72 0 Good
10 Start/Stop Count 98 2621 Very good
10 Reallocated Sector Count 100 0 Very good
7 Seek Error Rate 79 94732818 Good
6 Power On Hours Count 68 2524 Good
10 Spin Retry Count 100 0 Very good
10 Power Cycle Count 97 3480 Very good
10 Reallocated Event Count 100 0 Very good
10 Current Pending Sector 100 0 Very good
10 Offline Uncorrectable Sector Count 100 0 Very good
8 Ultra DMA CRC Error Rate 200 0 Very good

All of the attributes of your hard disk have normal values. This is good.

The overall fitness for this drive is 97%.
The overall performance for this drive is 97%.

Ok, kann mir das nun jemand definieren / enträtzeln?
Ist das dieser SMART-Test?